Online Quizzes

Building Cisco Mulitlayer Switched Networks (BCMSN)

    1. Selecting VTP version 2 instead of VTP version 1 is preferrable because VTP version 2 __________.

    Supports token ring VLANs
    Saves VLAN configuration memory
    Reduces broadcast traffic carried on trunk lines
    Reduces the amount of configuration necessary
    Allows active redundant links when used with spanning tree

    2. What does VLAN trunking protocol (VTP) do?

    Propagates global VLAN information
    Sets trunk priority levels of adjacent switches
    Ensures that there is a trunk or VLAN 1 operating
    Adjusts VLAN interswitch links to reduce parallel load sharing
    Maps the non-contiguous switch fabric across the global VLAN

    3. An Ethernet media trunk line is to be configured to operate in ISL mode between two Cisco Switches, each having identical modules, software revisions, and VLAN configuration information. Which of the following two are not required for the trunk to operate in ISL mode correctly?

    Identical speed at each end of the link
    Identical duplex at each end of the link
    Identical native VLAN parameters at each end of the link
    Identical trunk negotiation parameters at each end of the link
    Identical trunk encapsulation parameters at each end of the link
    Compatible trunking mode shared by the ports connecting the links at either end.

    4. You are configuring a VLAN trunk for fast Ethernet. Which trunking mode makes the port willing to convert the link into a trunk link?

    Auto
    Negotiate
    Designate
    Noneogiate

    5. You have configured a catalyst switch to operate in VTP mode. On your switch you cannot create, change or delete VLANs. Which VTP mode is your switch in?

    Host
    Native
    Client
    Server
    Transparent

    6. You have several VLAN trunks in Auto and Off modes. You are entering a new port. Which modes must you select for the port to be in permanent trunking mode?

    On
    Off
    Auto
    Desirable
    Nonegotiate

    7. You are configuring a VLAN on a fast Ethernet. Which two trunking modes make the port able to convert the link to a trunk link?

    Off
    Auto
    Desirable
    Negotiate
    Non-negotiate

    8. An Ethernet media trunk link is configured and is operating between two Cisco switches. Each switch has identical modules, software revisions, and VLAN configuration information. Spanning tree protocol is disabled on all VLANs. Problems have been identified regarding frames leaking between two VLANs. What is the most likely cause of this problem?

    The duplex mode is different at each switch
    The link is using IEEE 802.1Q protocol in point-to-point mode
    The link is using 802.10 trunk protocol with the SAID parameters incorrectly set
    The link is using ISL protocol and the native VLAN information is different at each end of the link
    The link is using IEEE 802.1Q protocol and the native VLAN information is different at each end of the link

    9. You need to enter a switch into an existing VTP domain without altering the configuration of the systems currently on the domain. Which two conditions ensure that the new switch will not change the existing VTP domain configuration?

    The switch must be in client mode
    The trunk links must not be configured for ISL
    The VTP domain must not have a password assigned to it
    The ''clear config all'' command must be executed on the switch and the switch must be rebooted

    10. An Ethernet media trunk line is to be configured between two Cisco switches, each having identical modules, software revisions and VLAN configuration information. Which two of the following are required for the trunk to operate?

    The link is 100Mbps or slower
    The link uses IEEE 802.1Q trunk protocol
    The link must be point to point if it is ISL
    The link must have different trunk encapsulation at each end
    The link may use IEEE 802.1Q trunk protocol, providing the SAID parameter is correctly set

    11. Which statement best describes a trunk link?

    The trunk link belongs to a specific VLAN
    A trunk link only supports a native VLAN for a given port
    Trunk links use 802.10 to identify a VLAN over an Ethernet backbone
    Trunk links are used to connect multiple devices on a single subnet to a switch port
    The native VLAN of the trunk link is the VLAN that the trunk uses if that link fails for any reason

    12. You are troubleshooting problems on a Catalyst 5000 trunk and you notice that there is disagreement about the VLAN configured to use the trunk. What can you do?

    Remove all the VLANs set for the trunk
    Reload the active VLAN configuration settings
    First clear the affected port and then bring it back up
    Explicitly set or clear the trunk for the VLAN to be on
    Set or clear VLANs on both sides of the link so values do not match

    13. When checking that a switch and router are consistently configured for VLANs, Cisco engineers typically recommend that VLAN ID 1 _______.

    Has a maximum transmission unit of 4352
    Be configured for concurrent routing and bridging
    Be used for management and troubleshooting only
    Use an ID that is identical to the default SAID value
    Span a network diameter of no more than eight devices

    14. What does it mean when LEDs falsh during the Catalyst 5000 power up sequence?

    One or more modules is not correctly inserted into its slot
    The power up sequence is underway and not yet completed
    A fan, power supply, or supervisor clock is disabled
    The network management autodiscovery process is under way
    The traffic testing process of an interface loopback has not yet completed

    15. For an indicator of an active link state on a Catalyst port, you should look at the _______.

    Port's link LED on the Switching Module
    Port Link OK LED on the Link Integrity Module
    Status LED on he Network Management Module
    Solid green LED on the port''s Route Switch Module
    Switch link load LED on the Supervisor Engine Module

    16. What command must you use to enable CGMP on a router interface?

    ip cgmp
    pip cgmp
    ip pip cgmp
    interface cgmp

    17. In order for CGMP to operate correctly on a switch, the switch must have a network connection to a ________ .

    Switch running IGMP
    Router running CGMP
    Switch running CGMP
    Switch that has VLAN configured

    18. Which command is used to disable CGMP on a set command-based switch?

    disable cgmp
    set cgmp off
    shutdown cgmp
    set cgmp disable

    19. You are preparing to install a UTP cable connection. You should have no more than ________.

    Five meters from the switch the patch panel
    Ninety meters from the punch down block to the switch
    Ten meters from the punch down block to the desktop connection
    Fifty-five meters from the patch panel to the office punch down block

    20. To configure a fast Ethernet connection between your access switch and primary distribution switch, which two steps are highly recommended?

    Set the port speed on your access switch
    Assign and IP address to your access switch
    Set the port speed on your primary distribution switch
    Set the port duplex on the primary FE mod/port on your access switch

    21. When setting duplex on a Catalyst 1900 series switch backup link, the auto argument ________ . (choose two)

    Is only valid on a 10baseT port
    Is the default for the 100baseTX port
    Negotiates full duplex connectivity with the connecting device
    Places 100baseTX port into full duplex mode with flow control

    22. You have connectied a cable between a Catalyst 1900 and 5000 series switch. When correctly connected, the port status LED light located on __________.

    Both switches should NOT light up
    Both switch should light up and remain on
    Both switch should stay lit for 60 seconds, then turn off
    The catalyst 1900 lights up for 30 seconds, then turns off, and the catalyst 5000 port status LED stays lit
    The catalyst 5000 lights up for 30 seconds, then turns off, and the catalyst 1900 port status LED stays lit

    23. You IS managare has assigned you to configure a backup link on an IOS-based command switch. Which command must you use to configure the interface/port for full duplex?

    duplex
    duplex full
    full duplex
    duplex auto
    port duplex full

    24. Which two of the following does Ethernet LAN switch use?

    MPOA
    IEEE 802.10
    IEEE 802.1D
    Multicast OSPF
    Spanning-Tree Protocol

    25. You have a link between your distribution and core switches that is configured for auto-negotiation. To ensure the most efficient connection, which duplex mode would you select?

    Half
    Full
    Auto
    Full-flow-control

    26. You have a set-based switch. Which command do you enter to assign an IP address to an interface?

    IP address
    set ip address
    set interface sc0
    interface ethernet

    27. You want to use hardware-based bridging to switch between Ethernet and Fast Ethernet, and you need to increase network bandwidth. However, you do not want to make an expensive network overly complicated. Which ISO layer is associated with these functions?

    Session
    Network
    Data Link
    Physical
    Transport
    Application
    Presentation

    28. Which switch command is required to configure a functional Ethernet connection between an end-user station and the access layer switch?

    IP address
    Enable access
    Interface ethernet
    Configuration ethernet
    None of the above

    29. What are two solutions for carrying VLAN over a single link?

    ISL
    IGRP
    CGMP
    802.1q

    30. Which statement accurately describes the condition of VTP before you can assign ports to VLAN 1 on a switch?

    VTP configuration does not affect this action.
    VTP is configured and the mode on this switch is client.
    VTP is configured and the mode on this switch is server.
    VTP domain name has not been configured on this switch.
    VTP is configured and the mode on this switch is transparent

    31. Before you can modify one of the VLAN names on a switch, the VTP domain name _______. (choose two)

    Must not be configured on the switch
    Is configured and the mode on the switch is client
    Is configured and the mode on the switch is server
    Is configured and the mode on the switch is transparent

    32. You have several separate VLANs that you want to interconnect. Which type of device allows connections between VLANs?

    Core Switch
    IP translator
    Router processor
    VLAN interswitch
    Switching engine

    33. To ensure that a route processor can forward traffic from multiple VLANs, you must first _________.

    Define a default gateway on the RSM
    Assign the interface to a VTP domain
    Configure a unique VLAN number on each interface
    Define the ISL encapsulation type and number on each interface

    34. In a switch internetwork, which two situations would cause broadcast traffic to be contained within the physical segment?

    Host interface is constantly sending IGRP requests
    Host interface is constantly sending frame fragments
    Host interface is constantly sending IP echo requests
    Host interface is constantly sending broadcast frames
    Host interface is constantly sending frames with CRC errors

    35. How many global MAC addresses does the RSM have that apply to interfaces on that device?

    1
    16
    256
    1024

    36. You have an IOS-based command switch that you want to define the default gateway on. Which command do you use in global configuration mode to configure the switch?

    Set IP route
    IP default route
    ip default-gateway
    set default-gateway

    37. With VLAN routing, a switched VLAN corresponds to a(n) _________.

    Bridge group
    Media interface
    ISL trunk interface
    Single routed subnet
    Spanning-tree branch

    38. A company has redesigned its campus network to support three switch blocks that broadcast domains to each individual switch block, while still allowing inter-VLAN routing within and between switch blocks. What is the most appropriate device at the distribution layer?

    Catalyst 8500 series switch
    Catalyst 4000 series switch
    catalyst 5000 series switch with an internal RSM
    Catalyst 1900 with a two-port 100BaseTX uplink module

    39. The engineering department wants to interconnect users on multiple floors in the same building. To date, the department has only ten users but plans to double that number in the next eight months. The engineers need to access CAD/CAM documents on the workgroup servers. What is the most appropriate access layer device?

    Catalyst 8500 series switch
    Catalyst 5500 series switch
    Catalyst 1900 series switch with 100BaseTX ports
    2900 series switch with 100BaseTX ports

    40. The multilayer switch module is viewed as an external router connected to four full-duplex Gigabit ethernet interfaces by the Catalyst _______ series switches. (choose two)

    4000
    5000
    6000
    6500
    2924G

    41. A company has experienced 300 percent growth over the last year and has recently installed a new multimedia center for distributing company information throughout the campus. The company has requirements for gigabit-speed data transfer, high-availability, and inter-VLAN routing between the end user and the enterprise server farms. What is the most appropriate device for the distribution layer?

    Catalyst 8500 series switch
    Catalyst 1900 series switch with 12 10BaseT ports
    Catalyst 4000 series switch with 6-port gigabit ethernet module
    Catalyst 6000 series switch with 16-port gigabit ethernet module

    42. A company has a small network with about 25 users. They need to connect individual desktops and 10BaseT hubs to high-speed distribution switches that can work in conjunction with a 7x00 series external router. Which combination of hardware meets the minimum requirements of the network at this company?

    A catalyst 1900 series switch and a 2926G switch
    A 2926 switch and a catalyst 8500 series switch
    A catalyst 4000 series switch and a catalyst 6500 series switch
    A catalyst 1900 series switch and a catalyst 8500 series switch

    43. The multicast IP address 224.64.225.45 translates to which MAC address?

    01-00-5E-28-FF-2D
    01-00-5E-40-FF-2D
    01-00-5E-40-FF-45
    01-00-5E-C0-FF-2D
    01-00-5E-C0-FF-45

    44. In which transmission method are frames replicated as needed?

    Unicast
    Multicast
    Simulcast
    Broadcast

    45. IGMP query messages are addresses to all-host groups with the TTL set to one. What is the purpose of setting the TTL to one?

    All multicast routers will see IGMP query messages.
    All multicast routers forward IGMP query messages.
    IGRMP query messages are flooded throughout the switch block.
    IGMP query messages remain on the directly-attached subnetwork.

    46. Which statement about multicast transmission is true?

    One copy of each packet is sent to every client.
    A new packet is sent each time the client requests it.
    Only one copy of each packet is sent using an address that reaches all the clients.
    Only one copy of each packet is sent, using a special address that allows each client to choose if they receive the packet.

    47. You are in the process of creating a flow mask. You have created an extended access-list. Which command applies it to the interface?

    Group add
    IP access-group
    Access extended list
    Interface extended list

    48. You need to configure your distribution layer switching engine to participate in multilayer switching. Which command must you use?

    set mls on
    set mls start
    set mls se IP
    set mls enable

    49. Which command enables global multilayering on the distribution layer route processor?

    mls rp ip
    mls enable
    mls rp vtp-domain
    mls rp management-interface

    50. Which command displays the MLS cache?

    show mls
    show mls rp
    show mls list
    show mls entry

    51. Applying an outgoing access list to an interface ________.

    Results in no action taken by the MLS-SE
    Generates an MPLS message from the MLS-RP to the MLS-SE
    Purges any entries for flows on that interface and records no new entries
    Records enable packets only if the administrator sets the MLS RP IP ACL command on the interface
    Causes the MLS-SE to retain the MLS cache entries until they age out and no longer record any new entries

    52. Which command enables an RSM interface for multilayer switching?

    mls on
    mls rp ip
    set mls start
    set mls enable

    53. Multilayer switching is based on the _______ model.

    "switch one, route many"
    "route once, switch many"
    "switch only Layer 3 and below"
    "route when you can, switch when you must"
    "switch on Layer 3 frames, route on Layer 2 packets"

    54. Which command would you use if you want to observe the spanning-tree port state (e.g. disable, blocking, listening, forwarding) on a set command-based switch?

    show port
    show span
    show spantree
    show config spanning
    show spanning-tree port

    55. Once the failure of a forwarding link is detected, which functionality allows a blocked port of a switch to quickly begin forwarding?

    PortFast
    UplinkFast
    BackboneFast
    SwitchlinkFast

    56. Which modifications can be made to the spanning-tree protocol to improve spanning-tree protocol operations as a network grows?

    Properly place the root bridge to ensure an optimal STP topology.
    Provide for efficient workstation access through the use of BackboneFast.
    Load balance on redundant links through the use of technologies like BackboneFast.
    Configure access switched as root bridges to ensure optimal workstation access to the network.
    Improve the convergence time of spanning tree during a network reconfiguratiuon tree by decreasing the forward delay timers.

    57. How can you reduce spanning-tree protocol BPDU traffic during extended periods of instability for VLANs?

    Make the router the root bridge.
    Change the router to VTP server mode.
    Set forward delay and max-age timers to maximum values.
    Combine all the VLAN spanning trees into a single spanning tree.
    Change the spanning-tree protocol encapsulation from IEEE to DEC.

    58. Your network has many point-to-point connections that are all part of the switch fabric. However, they are still running spanning tree. This causes each port to wait as long as 50 seconds before data can be sent. Which feature can be enabled to significantly decrease the time of the listening and learning states?

    PortFast
    UplinkFast
    BackboneFast
    Redundantlink
    RedundantPort

    59. In spanning-tree protocol, what is the default transaction time for a switch to move from blocking to forwarding state?

    5 seconds
    50 seconds
    60 seconds
    90 seconds

    60. The first step in spanning tree is to determine a root bridge. Which factor or factors determine who will become the root bridge?

    The port ID
    The port cost
    The combination of the path cost and the MAC address
    The combination of the priority number and the MAC address

    61. You need to take advantage of the Fast EtherChannel ports. Which two guidelines help avoid configuration problems that may cause a port to be automatically disabled?

    Allows some ports in a channel to be disabled.
    Configure the ports in a channel as dynamic VLAN ports.
    Configure all ports in a channel to operate at the same speed and duplex mode.
    Assign all ports in a channel to the same VLAN or configure them as trunk ports.

    62. Catalyst 5000 troubleshooting begins with the Catalyst 5000 module located in the top slot of the chasis. What does this slot contain?

    Ping and telnet utilities in the route switch module.
    Console and network ports in the supervisor engine module.
    Three fast Ethernet ports that can connect to other systems.
    Interface module with LEDs to indicate errors and load factor.
    Embedded RMON, SwitchProbe, and switched port analyzer.

    63. When using the Catalyst 5000 series switch SPAN feature, the function of the destination module/port identifier is to identify __________.

    The destination of ISL packets on another switch
    The port that mirrors traffic to a protocol analyzer
    The destination of ISL packets on the outbound switch
    The destination of spanning-tree BPDU to the root bridge
    The destination portion or a MAC source/destination address pair

    64. The high end of the tools for trouble-shooting and managing catalyst switches is composed of the graphic user interface applications in __________.

    CWIS
    NetSYS
    CiscoView
    VLANDirector
    Traffic Director

    65. What is the switch set-based command that is comparable to the Cisco IOS-based command, 'show span.'?

    show port
    show vlan
    show trunk
    show spantree
    show switchport

    66. Which command would you use to check a module/port to display the trunking status, VLAN active status, and VLAN that can use a particular link?

    show span
    show vlans status
    show vtp domain info
    show [module/port] trunk
    show trunk [module/port]

    67. In contrast to shared Ethernet, switched ethernet on a catalyst switch ________. (choose two)

    Provides greater access to bandwidth
    Connects directly to end users or other switches
    Users software to set up and maintain a filtering database
    Has fewer utilities, which makes management more difficult
    Is usually limited to a maximum of 16 ports and 2 spanning trees
    Associates a MAC source address with a set of ports for transmission

    68. When connecting 10BaseT switch ports to servers, workstations, and routers, make sure that you use _________.

    A crossover cable
    A straight-through cable
    A RJ-to-RJ-45 rollover cable
    MMF cable, with a 62.5-micron fiber-optic core and a 125-micron outer cladding.

    69. Which type of cable is used to connect switch 10BaseT ports to a 10baseT-compatible workstation?

    Thick coaxial cable
    Crossover CAT5 cable
    Straight-through CAT5 cable
    RJ-45-to-RJ-45 rollover cable

    70. Shared bandwidth and switched bandwidth are some of the functions represented by which layer in the campus network hierarchical model?

    Core
    Access
    Network
    Distribution

    71. Which statement about port security is true?

    It allows a network administrator to configure a set of allowed devices or IP addresses to provide additional security.
    It moves all ports, except the console, out of the management VLAN to prevent unauthorized access to the default VLAN.
    It limits the number of MAC addresses that are allowed to use the switch to prevent unauthorized users from gaining access to the network.
    It must be enabled on a switch port and the directly attached router interface in order for the switch to build a table of allowable MAC addresses.

    72. What is the IEEE specification for Gigabit Ethernet?

    IEEE 802.1P
    IEEE 802.1Q
    IEEE 802.3Z
    IEEE X3T.11

    73. If you configure a switch as a VTP server offline and then connect it to the network, the switch may __________.

    Revert to client mode once you enable online access
    Not get root bridge or designated bridge information
    Destabilize the spanning tree as the server attempts to become root bridge
    Ignore the configuration revision numbers created on the other VTP servers
    Cause a loss of VLAN information by advertising an innacurate revision of the domain

    74. When using VTP, what VTP information does a catalyst switch advertise on its trunk ports? (choose two)

    Native VLAN
    Negotiona status
    Spanning-tree bridge
    Management domain
    Configuration revision number

    75. An Ethernet media trunk link is to be configured to operate in ISL mode between two Cisco switches, each having identical modules, software reviouns and VLAN configuration information. Which condition would prevent the trunk link from operating in ISL trunking mode?

    The trunk encapsulation is different at each end of the link.
    The duplex parameter is set to AUTO at each end of the link.
    The native VLAN paramater is set to AUTO at each end of the link.
    The speed parameter is set to AUTO at each end of the link.
    The trunk negotiation parameter is different at each end of the link.

    76. Which two statements about VLANs are true? (choose two)

    A trunk link does not have a native VLAN.
    A trunk link does not belong to a specific VLAN.
    All VLANs can be tranported over a single trunk link.
    There are 4 identification techniques to determine which VLAN a frame belongs to when it is received on a trunk link.

    77. An Ethernet media trunk is to be configured between two Cisco switches, each having identical modules, software revisions and VLAN configuration information. Which statement about the trunk link is false?

    The link may be 100Mbps or faster.
    The link may be ISL and be point-to-point.
    The link may use 802.1q trunk protocol, providing the SAID parameter is correctly set.

    78. In a VTP domain, a catalyst switch advertises ________.

    The VLAN ID of all known VLANs, the management domain name, and the total nuber of trunk links on the switch
    The VLAN ID of all known VLANs, a 1-bit canonical format (CFI indicator), and the switch configuration revision number
    The management domain name, the switch configuration revision number, the known VLANs, and their specific parameters
    A 2-byte TPID with a fixed value of 0x8100 for the management domain number, the switch configuratioin revision nunber, the known VLANs, and their specific parameters

    79. Which two statements about trunk links are true?

    A trunk link does not have a native VLAN.
    A trunk link does not belong to a specific VLAN.
    All VLANs can be transported on a single trunk link.
    There are four identical techniques to determine which VLAN a frame belongs to when it is received on a trunk link.

    80. Which parameter is NOT distributed by VTP advertisements?

    VLAN names
    VLAN descriptions
    VLAN domain names
    VLAN SAID number
    VTP configuration information

    81. Which MAC address is a multicast address?

    00-00-5E-12-2C-11
    00-00-5F-12-2C-11
    00-01-5E-12-2C-11
    01-00-5E-12-2C-11

    82. Which multicast ranges are reserved for local purposes and are not forwarded by multicast routers?

    224.0.0.0 through 224.0.0.255
    239.0.0.0 through 239.255.255.255
    255.0.0.0 through 255.255.255.255
    224.0.0.0 through 224.255.255.255

    83. Which definition correctly describes the broadcast transmission method?

    One copy of each frame is sent to every client.
    A new packet is sent each time the client requests it.
    Only one copy of each frame is sent, using an address that reaches all clients.
    One copy of each frame is sent, using a special address that allows each client to decide if they want to receive the frame.

    84. Which two configurations must be satisfied before you enable multicast?

    NICs on the network must support MMNP.
    Hosts must have an IP protocol that supports multicast.
    Servers and clients must have applications that support IP multicast.
    Subnet boundaries must be configured for MOSPF multicast routing.

    85. A company needs to interconnect its four separate campus buildings with a high-speed, high-bandwidth backbone. Each building supports a separate department and each department supports IP, IPX, and AppleTalk. The network designer has already recommended a Catalyst 6000 series switch at the distribution layer. What is the most appropriate device for the core?

    Catalyst 8500 series switch
    Catalyst 2926G series switch
    Catalyst 4000 series switch with a 6-port Gigabit ethernet module
    Catalyst 5000 series switch with a 24-port group switch 1000baseT ethernet module

    86. Which Cisco series Catalyst is used with small/medium campus networks, and connected desktops and 10BaseT hubs to distribution switch with high-speed connections?

    Catalyst 2820
    Catalyst 4000
    Catalyst 5000
    Catalyst 6000

    87. The router switch feature card is a full-function IOS router installed as an integrated daughter card for the _________.

    Catalyst 4000 series switch
    Cisco 7500, 7200, 4500, and 4700 series routers
    Catalyst 5000 series supervisor IIG and supervisor IIIG cards.
    Catalyst 5000 series supervisor engine III, FSX, or III FLX modules.

    88. Which two Cisco series switches are the most effective for distribution layer switching?

    Catalyst 2800
    Catalyst 4000
    Catalyst 5000
    Catalyst 6000

    89. Which two events can cause an MLS entry to be purged from the cache?

    An access list is applied.
    MLS is enabled on a related switch.
    The flow for that entry is not detected for the specified aging time.
    A candidate entry is in the cache for three seconds with no enabled entry.

    90. Which command enables multilayer switching on a distribution layer switching engine?

    set mls sp IP
    set mls enable
    set mls rp vtp-domain
    set multilayer switching

    91. You are using multilayer switching, and you need to configure your distribution layer route processor to participate in the multilayer switching. Which two commands must you use when you configure the distribution layer route processor?

    mls rp ip
    mls enable
    mls run start
    mls rp vtp-domain

    92. Which two tasks must be completed to enable CGMP on a distribution layer device?

    Disable IGMP on the distribution router.
    Enable IGMP on the distribution switch.
    Disable IGMP on the distribution switch.
    Enable CGMP on the distribution switch.
    Enable CGMP on your distribution router.

    93. The router creates a CGMP frame _________.

    And forwards it to a well-known address, 224.0.0.1
    And forwards it to a well-known address to which all CGMP switches listen
    And forwards it to the rendevous point to ensure consistent configuration
    And assigns it a TTL equal to or less than the TTL assigned to the forwarding interface.
    Containing the request type, the multicast group address, and the actual MAC addresses of the destination devices.

    94. What is the default setting of CGMP on a Cisco switch?

    Enabled
    Disabled
    Enabled only when PIM switch is detected
    Disabled only if multicast is not detected

    95. To determine the best loop-free path to the root, the spanning tree protocol __________.

    Places the port with the highest port ID in the forwarding mode
    Places the port with the lowest port ID in forwarding mode
    Attaches the lower port cost values to ports supporting slower media
    Places the port with the lowest forwarding delay timer in forwarding mode
    Uses the network_diameter paratemer in the set spantree root command

    96. A catalyst physical port operating as a trunk can be part of several spanning trees. On this shared topology, loops in one spanning tree ________.

    Are segmented from the other spanning trees
    Do not have any impact on the other spanning trees
    Can have a media load impact on the other spanning trees
    Use a time-to-live mechanism to put an end to loop pollution
    Can be isolated from the other spanning trees with root port settings

    97. You have a spanning tree environment. Which command ensures timely host access to the network?

    set spantree portfast enable
    set spantree superlink enable
    set spantree uplinkfast enable
    set spantree backbonefast enable

    98. You want to take advantage of the benefits of parallel bandwidth provided by fast EtherChannel. To enable fast EtherChannel, enter _________.

    set link channel
    set port channel
    set channel fast
    set ether channel

    99. When should PortFast be used?

    When you are connecting a single end station to a switch port
    When you need several switch ports to connect a signel port
    When you have switch ports connected to a single end station
    When you are using the Uplink Fast Protocol and want to increase the port tie on several end stations connected to a signel switch port

    100. Default gateways can exist on two types of switches. You enter the 'set IP route" command to configure a default route on a(n) _____ -based command switch.

    Set
    IOS
    Forward
    Interface

    101. Which command accurately depicts the mode and command used to configure a default gateway on an IOS command-based switch?

    Switch(config)# IP route ipaddress
    Switch(enable)# set IP route ipaddress
    Switch(enable)# ip route-default ipaddress
    Switch(config)# ip default-gateway ipaddress
    Switch(enable)# set ip default-gateway ipaddress

    102. What is the maximum number of VLANs supported on a single RSM?

    1
    16
    256
    1024

    103. Which statement correctly identifies the characteristics of static VLAN members?

    VLAN membership is managed through port-based assignments.
    VLAN membership is managed through a database that maps MAC addresses to specific VLANs.
    The port can be automatically changed to another VLAN, based on a device MAC address in a VLAN database.
    As soon as the port has been assigned to a VLAN, the port is capable of sending or receiving frames from devices in another VLAN.

    104. You have several separate VLANs that you want to interconnect. Which type of device allows conection betwen VLANs?

    Core switch
    IP translator
    route processor
    VLAN interswitch
    Switching engine

    105. You have been asked if there are any issues concerning connecting a host that is attached to the network using IEEE 802.5 and another host that is attached to the network using IEEE 802.3. The preference is that they be in the same VLAN and only be processed at Layer 2. Which two statements are true?

    There is an issue with the VLAN media mismatch at layer 2.
    There is an issue at layer 2; it requires the use of the SAID field.
    There is an issue at layer 2; it requires the use of transparent bridging.
    There is an issue at layer 2; it requires the use of translational bridging.
    There is no an issue with VLAn membership; it is not media dependant.